07 Dec Spa Codes and Meaning

If your spa’s topside control has a code displaced and you’re not sure what it indicates, we’re here to help. Please see the below codes and it’s corresponding meaning.

CODE	MEANING
	INDICATES THE SPA IS RUNNING ITS PRIME CYCLE. THIS WILL LAST FOR ABOUT 3-5 MINUTES AFTER THE SPA IS POWERED UP.
	INDICATES STANDBY MODE HAS BEEN ACTIVATED. PRESS ANY BUTTON OTHER THAN JETS 1 TO RESUME NORMAL OPERATION.
,	INDICATES THE SPA IS IN ECONOMY MODE.
,	INDICATES THE SPA IS IN SLEEP MODE.
,	INDICATES THE SPA IS IN STANDARD MODE.
	INDICATES THE SPA IS IN STANDARD IN ECONOMY MODE. DURING THIS TIME THE SPA ACTS AS IF IT IS IN STANDARD MODE. AFTER ONE HOUR THE SPA WILL REVERT BACK TO ECONOMY MODE.
	INDICATES THE SPA IS SET TO FILTER 1 OUT OF EVERY 12 HOURS
,	INDICATES THE SPA IS SET TO FILTER 2 OUT OF EVERY 12 HOURS
	INDICATES THE SPA IS SET TO FILTER 3 OUT OF EVERY 12 HOURS
,	INDICATES THE SPA IS SET TO FILTER 4 OUT OF EVERY 12 HOURS
	INDICATES THE SPA IS SET TO FILTER 5 OUT OF EVERY 12 HOURS
,	INDICATES THE SPA IS SET TO FILTER 6 OUT OF EVERY 12 HOURS
	INDICATES THE SPA IS SET TO FILTER 7 OUT OF EVERY 12 HOURS
,	INDICATES THE SPA IS SET TO FILTER 8 OUT OF EVERY 12 HOURS
	INDICATES THE SPA IS SET TO FILTER 9 OUT OF EVERY 12 HOURS
	INDICATES THE SPA IS SET TO FILTER 10 OUT OF EVERY 12 HOURS
	INDICATES THE SPA IS SET TO FILTER 11 OUT OF EVERY 12 HOURS
, ,	INDICATES THE SPA IS SET TO FILTER CONSTANTLY
	REMINDER CODE TO TEST AND ADJUST PH LEVELS (EVERY 7 DAYS)
	REMINDER CODE TO TEST AND ADJUST SANITIZER LEVELS (EVERY 7 DAYS)
	REMINDER CODE TO REMOVE, CLEAN, AND REINSTALL FILTER (EVERY 30 DAYS)
	REMINDER CODE TO TEST AND RESET GFCI BREAKER/CORD (EVERY 30 DAYS)
	REMINDER CODE TO DRAIN AND REFILL SPA (EVERY 90 DAYS)
	REMINDER CODE TO CLEAN AND CONDITION SPA COVER (EVERY 180 DAYS)
	REMINDER CODE TO CLEAN AND CONDITION WOOD (EVERY 180 DAYS)
	REMINDER CODE TO REMOVE AND INSTALL NEW FILTER (EVERY 365 DAYS)
	REMINDER CODE TO INSTALL NEW MINERAL CARTRIDGE (AS NEEDED)
**USER MAY SUPPRESS ALL REMINDERS IN USER PREFERENCES.
	ERROR CODE INDICATING THERE IS AN INADEQUATE AMOUNT OF WATER, A FLOW ISSUE, OR AIR BUBBLES WITHIN THE HEATER TUBE. SPA IS SHUT DOWN FOR 15 MINUTES.
,	ERROR CODE INDICATING THERE IS AN INADEQUATE AMOUNT OF WATER, A FLOW ISSUE, OR AIR BUBBLES WITHIN THE HEATER TUBE. THIS IS DISPLAYED ON THE THIRD OCCURRENCE OF “dr”. SPA IS SHUT DOWN UNTIL MANUALLY RESET. TO RESET, PRESS ANY BUTTON.
,	ERROR CODE INDICATING THERE IS A SUBSTANTIAL DIFFERENCE BETWEEN THE TEMPERATURE SENSORS. THIS COULD INDICATE AN INADEQUATE AMOUNT OF WATER, A FLOW ISSUE, OR AIR BUBBLES WITHIN THE HEATER TUBE. TO RESET, PRESS ANY BUTTON.
	ERROR CODE INDICATING A PERSISTENT LOW FLOW ISSUE. MESSAGE APPEARS ON 5TH OCCURRENCE OF “HL” OR “HFL”. HEATER IS SHUT DOWN. TO RESET, PRESS ANY BUTTON.
,	ERROR CODE INDICATING ONE OF THE TEMPERATURE SENSORS HAS DETECTED A TEMPERATURE OF 110 DEGREES FAHRENHEIT. AFTER TEMPERATURE LOWERS SPA WILL RESET.
,	ERROR CODE INDICATING ONE OF THE TEMPERATURE SENSORS HAS DETECTED A TEMPERATURE OF 118 DEGREES FAHRENHEIT. AFTER TEMPERATURE LOWERS SPA WILL RESET.
,	ERROR CODE INDICATING THE TEMPERATURE SENSORS ARE OUT OF BALANCE. IF CODE IS FLASHING INTERMITTENTLY WITH THE TEMPERATURE OF THE SPA IT MAY BE A TEMPORARY ISSUE. IF THE COD IS DISPLAYED SOLID AND BY ITSELF THE SPA IS SHUT DOWN.
,	ERROR CODE INDICATING THAT SENSOR A IS EXPERIENCING AN ISSUE. SPA IS SHUT DOWN. MAY APPEAR TEMPORARILY IN AN OVERHEAT SITUATION AND DISAPPEAR ONCE HEATER COOLS.
,	ERROR CODE INDICATING THAT SENSOR B IS EXPERIENCING AN ISSUE. SPA IS SHUT DOWN. MAY APPEAR TEMPORARILY IN AN OVERHEAT SITUATION AND DISAPPEAR ONCE HEATER COOLS.
,	ERROR CODE INDICATING THE SPA HAS DETECTED POTENTIAL FREEZING CONDITIONS. SPA HEATER IS SHUT DOWN BUT PUMPS WILL RUN CONTINUOUSLY UNTIL TEMPERATURE OF SPA WATER INCREASES ABOVE 45 DEGREES FAHRENHEIT.
,	INDICATES THE TEMPERATURE OF THE SPA IS NOT CURRENT. THIS CAN BE DISPLAYED IMMEDIATELY AFTER THE SPA IS POWERED ON OR IN BETWEEN FILTER CYCLES WHILE THE SPA IS IN ECONOMY OR SLEEP MODE.
	ERROR CODE INDICATING THE PH OF THE SPA IS TOO LOW.
	ERROR CODE INDICATING THE PH OF THE SPA IS TOO HIGH.
	ERROR CODE INDICATING THE SANITIZER OF THE SPA IS TOO LOW.
	ERROR CODE INDICATING THE SANITIZER OF THE SPA IS TOO HIGH.
	ERROR CODE INDICATING THERE IS A CONFIGURATION ERROR WITHIN EITHER THE PROGRAMING OF THE SPA PACK OR THE DIP SWITCHES ARE NOT SET PROPERLY. SPA WILL NOT START.
	ERROR CODE INDICATING THAT THE FIRMWARE OF THE SPA PACK WAS NOT INSTALLED PROPERLY
	ERROR CODE INDICATING A HARDWARE FAILURE.
	ERROR CODE INDICATING A HARDWARE FAILURE.
	ERROR CODE INDICATING THAT THE SPA COULD NOT TRIP THE GFCI BREAKER. CONTINUED USE OF THE SPA MAY BE HAZARDOUS.
	ERROR CODE INDICATING THAT THERE APPEARS TO BE A PUMP THAT IS STUCK ON. THIS MAY CAUSE THE TEMPERATURE OF THE SPA TO RISE TO UNSAFE CONDITIONS.
	ERROR CODE INDICATING THAT A PUMP APPEARS TO HAVE BEEN STUCK ON THE LAST TIME THE SPA WAS UNDER POWER.
	CODE INDICATING THE PUMP IS OPERATING DURING STANDBY MODE TO ASSIST IN DRAINING THE SPA. PRESS JETS 1 TO TURN OFF PUMP AFTER WATER HAS BEEN DRAINED.
	ERROR CODE INDICATING A COMMUNICATION ISSUE BETWEEN THE PACK AND TOPSIDE.